• All safety, firefighting, lifesaving, and medical equipment.


• New running rigging


• Replacement of spares


• New Sail Drives January 2025


• New bottom paint January 2025


• Onan Generator Service including oil / filter change January 2025


• W3 service on Yanmar (all work done by authorized Yanmar dealer/service center/ Boatswains' locker + List Marine)


• Full service of Gori Props


• Replacement of all bilge pumps


• New aft deck table with slide option


• AC/ heating system serviced and recharged January 2025


• Solar panel replacement


• New Inverter January 2025 (Victron 8000)


• New plumbing for propane


• Full winch service


• New B+G mast displays


• Vessel is digitally managed via Vessel Vanguard with all service records, vessel documentation, maintenance records are current.


• Full Wax January 2025


• Tech deck cleaning January 2025.


• Starlink added January 2025

HULL AND DECK STRUCTURE

• Infused Carbon/Epoxy, construction


• Composite sandwich construction, post-cured in oven, for maximum strength


• Thermo formed foam core, to increase strength and reduce weight


• Constructed in female molds for minimum construction weight


• Additional carbon fiber reinforcing in highly loaded areas


• Carbon fiber longitudinal stringers and ring frames


• Sacrificial 'false' bow and forefoot in case of impact


• Watertight bulkheads to seal off bow and stern compartments


• Additional watertight compartments in each hull


• Structural composite hull floors to save weight and add stiffness


• Carbon fiber chain plates

APPENDAGES

• Symmetric curved ("C") Daggerboards, 6m long, constructed with prepreg carbon epoxy spars, carbon shear webs and carbon fiber skins determined by MM.


• Curved dagger board cases constructed with vacuum bagged, carbon fiber, epoxy, foam sandwich construction


• Self-Aligning High Modulus Plastic top and bottom bearings


• Antal, 1200 Watt electric line drivers for raising and lowering of daggerboards


• Dagger board proximity sensors added, 2020


• High aspect spade rudders, carbon stocks, and carbon construction in self aligning watertight bearings


• 2 x additional shallow draft carbon rudders for cruising

FINISHES

• Awlgrip / Alexseal exterior/interior paints


• Hard semi-ablative Antifoul on hull bottoms


• Gloss paint on some bulkheads, interior hull and ceiling surfaces


• Synthetic liner on hull and ceiling surfaces


• Rolled grey barrier paint in bilges


• Exterior storage lockers: carbon surfaces sealed


• Ring frames and stringers in rolled white barrier paint


• Interior doors in gloss paint


• Teak veneer interior joinery


• Rolled matte white paint inside cabinetry


• All vertical joinery surfaces finished in open-grain matte varnish


• Interior floors and table tops finished in gloss filled-grain varnish


• Galley and head counters finished in Corian


• Seating upholstery in Ultra Leather

RIG

MAST - Southern Spars

• Carbon fibre fractional non-rotating mast, mast head, spreaders


• Pre-preg Standard modulus carbon fibre autoclave baked for minimum voids


• Stainless Steel mast step, rocker style to allow variation of fore/aft mast rake and athwartship shroud stretch


• Integral shroud terminals at top of mast, loops at bottom


• Carbon fibre gooseneck with stainless steel pin.


• Mesh conduit for mast electrical cables


• Foldaway nylon steps to access main halyard


• Halyards lead to forward pit


• Halyard storage in forward pit


• 
  
  Halyards locks for: Staysail, fractional halyard (J0/ and Mainsail
  
  
  


• Main halyard, 1:1- 3 reefs - Harken ball bearing headboard car, Rigging Projects Headboard


• Fractional halyard, Bottom up furling A5


• Solent halyard, lashed off at top when raised.


• Staysail halyard, removable stay option, on constrictor when loaded


• Fixed Lazy Jacks lead to spreaders for easy sail hoisting


• 
  
  Spreader lights down, for coachroof and foredeck upward facing ( for reef points and main
  
  
  


• Topping lift 1:1


• Cunningham for mainsail and reefs - lead to winch


• Ion dispensing lightning protection connected to hull Dynaplate

BOOM Southern Spars

Pre-preg standard modulus carbon fibre autoclave baked for minimum voids
Box boom tube with stylised racks for mainsail stack with sheave boxes and locks for 3 reef lines lead fwd to mast and to winches in fwd pit
Pad eye and Spectra strop for lashing loose footed mainsail clew
Lazy jacks / new stack pack for main sail
Reef hooks (Karver) for reefs 1-3
In boom hydraulic ram, main sheet

LONGERON Southern Spars

Pre-preg standard modulus carbon fibre autoclave baked for minimum voids
Custom deep dual tapered section
3:1 Tack outhaul for Reacher tack
Carbon attachment points for the Solent forestay, Staysail tack, Reacher tack, Asym Tack
E6 - stays to each bow to end of longeron with lashed ends for articulation
Carbon section Pelican striker
Kevlar whisker stays attached to dolphin striker for vertical support

STANDING RIGGING

• Custom aramid forestay with furler (1) for Solent.


• Custom aramid lower (2) and cap (2) shrouds with loops to chain plates


• Custom carbon superior and inferior diamond with integral turnbuckles


• Custom carbon martingales with loops to chain plates


• Reacher torsional stay A5 on cable

SAILS - Doyle Sails - New 2022

• Main - Doyle 2022- Square Top, with 3 reef points


• Solent -,Doyle 2022 with UV leech protection and removable cover.


• Staysail - Existing North sail. Roller furling. Storable.


• A5 - Doyle 2022


• Asymmetrical - Downwind spinnaker, with snuffer.original A4 from North - 2020


• J0 Doyle Cableless sheeting inside the shrouds for light upwind or out outside for power reaching. And heavy air downwind.


• Set of spare sails: Main, Solent

RUNNING RIGGING -

• All shrouds, headstay, whisker/side stays, tramps, loops for shrouds, maringale replaced with k49, 2021


• Halyard control lines led to fwd pit


• Furling lines lead to fwd pit


• Sail control lines led to fwd pit


• Halyards and control lines equipped with lashing ends, including:


• Mainsheet - to traveler on line driver. On hydraulic ram in boom.


• Tack, cunningham and reef lines run to fwd pit


• Self tacking solent sheet run to fwd pit


• Self tacking staysail sheet run to fwd pit


• Reacher sheets - option to run to forward cockpit winches, or to aft cockpit winches


• Asymmetric sheets - option to run to forward cockpit winches, or to aft cockpit winches


• Main halyard 1:1 new halyard in 2021 loc king headboard car by harken 2021


• Staysail halyard 1:1 - on lock with 3:1 downhaul on tack


• Reacher / asymmetric halyard 1:1 on Hall lock. Tack on 3:1. A4 on 14mm Halyard, 1:1 with Karver lock at mast base and a Tylaska on a strop at the end of the longeron


• Loops or shackles for all blocks


• Furler lines continuous, for: J0 & A5


• Solent furler line (1)

DECK

GENERAL

• 3 Harken 990 's electric self tailing 24V winches with toe controls for all lines in fwd pit.


• 2 Harken 990's electric self tailing alloy 24V winches on aft beam with toe controls


• Winch Kill switches for all winches


• 10" aluminum winch handles with holders (2)


• Spinlock or constrictor clutches for control lines where needed:


• Harken self tacking jib track with pin stops


• Main sheet on hydraulic ram in boom - Harken hydraulic PCU


• Reacher sheet system consists of:


• 
  
  
  
  1. Harken blocks (2)
  
  
  
  


• 
  
  
  
  1. Harken padeyes (2)
  
  
  
  


• Mast base blocks, Harken floating 75, on soft lashings.


• Forward trampolines, with Spectra border line,


• Composite stanchions (1m) with three levels of Dyneema lifelines


• Lewmar 10 Flush deck hatches, one per head, with privacy screens


• Lewmar 44 Flush deck hatches, one per stateroom, with privacy screens


• Lewmar 4 opening port lights, one per stateroom and heads with privacy screens


• 2 x Goiot CE certified escape hatches


• Saloon & Topside windows, tinted toughened glass


• Passerelle with stanchions

DOCKING AND ANCHORING

• Lewmar retractable bow thruster


• Electric windlass, Lewmar V5, inside fwd underwing locker


• Rope/chain automatic gypsy sized for chain and 3-strand nylon anchor rode


• Rocna 40kg Anchor (1)


• Foldable Fortress anchor 21kg.


• Anchor rodes: 200' of 5/16" SS chain with 75' of nylon rode


• Bridles: Tylaska 2020 with custom mooring bridal, anchor bridal and storm bridal. As well as ancho strop connections.


• Anchor bridle padeyes on inboard hull sides forward with backing plates


• SS anchor roller exit fwd underwing


• Salt and fresh water wash down in anchor locker


• Eight 50' X 3/4" Mega Braid dock lines with chafe protected eyes


• Eight 30' x 3/4" Mega Braid dock lines with chafe protected eyes


• Four Fenders, 18x60 and x10 12'x36 with covers


• 8 Cleats

STORAGE LOCKERS-FORWARD OF MAST

• Large watertight stowage lockers on forward stbd and port bridgedeck.


• Large watertight genset locker on side of centerline forward of mast


• Windlass/chain locker, centerline forward of mast

BOW LOCKERS-PORT AND STB BOW

• Enormous watertight storage in bows for sails, hoses, fenders etc.

• 2 Yanmar diesel 4JH80 (80hp) with SD60 Saildrives (replaced 2019)


• Gorie Props, "Prop-Speed" on props


• Tachometer, fuel, hours, temperature, amp gauges


• Water temperature and oil pressure audio alarms


• ZF Controls


• Engine room ventilation blower with 3" ventilation hoses


• Custom composite engine silencer, muffler, and water lift with GenSep water separator, gas through under wing/chamfer panel and water below waterline


• Oil changers plumbed for engine and transmission in each engine box


• 2 x 375 Litre Polypropylene diesel fuel tanks with cleanout ports and appropriate baffles


• Filterboss fuel and water separators w/changeover valve for each fuel system


• Shut-off valve on fuel tanks


• Fuel tank 50mm SS deck fills, 1 per hull


• Fuel tank fuel transfer from Port to Stbd

• Inside steering Station: with1050mm carbon fibre sculptured race boat steering wheel


• Spade rudders with carbon fibre shafts designed and engineered by MM


• Carbon crossbar with low play bevel boxes and hardware to ensure rudder alignment


• Custom self aligning water tight rudder bearings (4)


• Water containment tube and water tight bulkhead in case of collision


• Auto Pilot attachment to Port and Stbd steering tiller


• Aft Tillers (removable) in carbon, with aft side deck helm seats in carbon, with custom control panel on armrest for sail and daggerboard controls.

• 2 Polypropylene 300 Litre water tanks


• 1 x Technicomar Sailor Compact 100 litre / hour with UV filters, 220VAC water makers.


• Hot and cold pressure water system in each hull


• Hot and cold pressure shower in Stbd transom


• 2 Isotemp 13 gallon hot water heaters 220v/75w and engine transfer heating, 1 each Port and Stbd


• Displacement pumps for steady pressure, less pump wear


• Electronic NMEA 2000 gauges for 2 water tanks, 2 waste tanks, and 2 fuel tanks


• Salt water wash down for decks, anchor rode, and windlass, one anchor locker, one aft stb transom


• Electric bilge pump system in each hull


• Portable emergency "Crash" manual bilge pump


• All sanitation hose odour resistant


• All flush mounted thru-hull fittings below waterline


• All seacocks labelled with tags


• All plumbing hoses are double clamped below waterline


• 2 deck fillers for removal of black water from tanks


• 2 black water tanks, 150l ea


• Filtration system for drinking water in galley with separate dispenser at sink

VENTILATION & HVAC

• Manual blinds for each deck hatch and windows in the living spaces.


• Air conditioning and reverse cycle heat system, 70,000 BTU


• Zoned air conditioning, saloon, 2 x Stbd cabins, 3 x Port cabins, (6)


• Custom fixed, acrylic, portlights in hull with Lewmar opening ports in each head, shower, berth

GENERAL

• Designed to ABYC regulation


• Shore power 220V


• Service in both 12 & 24 VDC and 220VAC


• 1 x Genset, Northern lights "Extra light" 6KW


• 2 x 24v 110A engine alternators


• 3.36KW Solar Panel Array - panels replaced 2021


• 720 amp/hr Lithium Ion Battery Bank (4 x 180amp hour with built in battery management system)


• 3 x Optima AGM starting batteries


• 2 x 24V 100amp Mastervolt Mass chargers (house chargers)


• 2 x 12/50A Mastervolt Charger masters (Ship's systems, engine start port starboard, genset start, radio battery)


• Inverter 24VDC 7000W


• 70,000 BTU Dometic air conditioning unit. With individual air handlers in each cabin and saloon.

ELECTRICAL OUTLETS

• 110v single outlets at:


• Galley (4)


• Nav (2)


• Cabins (5) One in each


• Heads (4) One in each


• Saloon (2)

LIGHTS

• LED Courtesy Lights in:


• Aft cockpit (4)


• Transom Steps (4)


• Companionways (6)


• Hull hallways (4)


• Heads and showers (8)


• Flush LED warm white spotlights in:


• Saloon ceiling above galley (10)


• Aft cockpit (4)


• LED reading Lights at:


• Nav station (1)


• Each berth, three at each Queen, and two at each single


• Heads (8) two in each


• LED navigation lights


• Stern light on aft edge of bimini


• Anchor light at masthead


• Steaming light on front face of mast


• Compass light


• Overhead dome lights in engine rooms, and transom and bow locker compartments


• 1 x Ocean LED underwater light on each transom (2 total)


• 2 x Upward facing mast lights on spreaders


• 4 x Trampoline lights


• Dinghy Davit Lights


• Boom Lights

• Base Navigation System - Helm Station x1, Nav Station x1


• B&G H5000 Zeus touch screen displays integrating radar/ chart overlay/ weather routing/ yacht systems/ autopilot/ performance numbers - system integrated with Ipod / laptop as remote display and control
  1x GPS Antenna
  B & G Hercules 5000 system processor
  1x Wind vane
  1x Sounder Module
  1x Thru Hull transducer
  1x 4G Radar Broadband System


• Additional
  ➢ B&G H5000 Analog Expansion Module
  ➢ B&G H5000 3D Motion Sensor

Auto Pilot System - Triton, Pilot add-on System

• 2x Triton Pilot Controller


• 2x Triton Pilot Computer


• 2x Rate Compass


• 2x Rudder Feedback Unit


• 1x Remote Commander system


• YACHT COMMANDER system for throttles, bow thruster, remote steering, windlass

Communications Base System

• Onboard Wi-Fi router


• 1x VHF MARINE RADIO, Simrad /B&G


• 1x VHF antenna


• 1x Class B AIS System with GPS antenna


• Upside up System


• CZone remote monitoring - with SENTINEL - added 2020


• (2) iPad Pro repeaters from B&G for Bucket seat steering

INSIDE HELMSTATION

• Custom carbon steering wheel


• Helm seat with Ultra-Leather wrapped 4" reticulate open cell foam cushions


• Push button controls for hydraulic bridle main sheet.


• Moonroof - glass, electric opening, by Webasto. For ventilation, and clear view of mainsail.

SALON

• 2x Toughened glass doors, for access to forward cockpit.


• High gloss carbon fiber designed features


• Teak veneer cabinetry


• Navigation/communication station on starboard side; ample room for electronics


• Custom manual blinds for the side and forward outboard saloon windows. Mounted behind custom ceiling moldings.


• Ceiling covering, stretched "Whisperwall"


• Settees (1) with Ultra-Leather wrapped 5" reticulate open cell foam cushions.


• Table in light veneer, approx 1.50 x 1m , adjustable to bed, if needed.


• Retractable TV, fold down from ceiling


• Electric Keyboard to Starboard, behind Navigation Station

GALLEY

• Galley working surface, Coriander.


• 4 burner Force 10 stove


• Double stainless steel sink with faucet


• Vitrifrigo fridge drawers below counter


• Vitrifrigo freezer drawers below counter


• Ample storage cabinets below counters


• Filtration system for drinking water in galley. With separate dispenser at sink.


• 1 ice maker


• 1 wine bar, capacity for up to 24 bottles

STATEROOMS (4) ENSUITE

• Queen sized (60" x 80" x 6") berth in cabins


• Planus Arctic electric toilet system


• (1x) "Jack& Jill" shower compartments, port and starboard hulls. With access from each head.


• Wall mounted shower with temperature controlled mixer

UTILITY ROOM (Starboard Stern)

• 1 Washer/Dryer

AFT COCKPIT, TRANSOM STEPS

• Sliding glass door to create large walk-through saloon access


• Walk-through access to transom steps


• Teak floor


• Settee with Ultra-Leather wrapped 5" reticulate open cell foam cushions.


• Exterior dining area with Ultra-Leather wrapped 5" reticulate open cell foam cushions.


• Storage lockers in settees and dining area


• Stainless steel folding swim stairs (75mm tread width) integrated in Stbd transom


• 2 Tables, one convertible to lounging.


• Outdoor hot-cold water shower at Stbd transom


• Two carbon dinghy davits with electric self contained lift winches with Up/Down controls, 500kg max dinghy / motor weight combined

ENTERTAINMENT

Saloon Entertainment

• Bose V25 Home Entertainment System with 5 x speakers


• Apple TV

Cockpit Aft Entertainment

• Bose 131 marine speakers 2

• Simplified "Upside Up" anti capsize system, with shroud load sensors and Mainsheet dump


• 8 Man life raft, Hand held VHF, Hailer/Foghorn, lifejackets


• MOB's with buttons

• 4.2M Carbon RIB tender, with Yamaha 50HP Outboard, and cover.